If the wash, rinse and spin function lights all flash at the same time, this would indicate a possible blockage in your filter or waste / drain pipe. If you do not have your manual, you can download it here.

Why is my Whirlpool washer wash light blinking?

The Wash Light is On or Flashing when the water level does not change for a period of time OR water is present but the control does not detect the water level changing.

How do you reset a Whirlpool washing machine?

Turn off the washer on the control panel. Unplug the washer for twenty seconds. Turn on the washer. If the process has worked, your washer will now be reset.

What causes a Whirlpool washer not to wash?

If your Whirlpool washer Not Spinning well, you need to check the pump. It could be clogged with debris or defective and needs to be replaced. To check the pump, disconnect the drain line and remove the back panel of your machine. Check for debris with a flashlight, or check with a special tool.

Why is my washing machine wash light flashing?

If the wash, rinse and spin function lights all flash at the same time, this would indicate a possible blockage in your filter or waste / drain pipe.

What does a flashing wash light mean?

The Wash Light is On or Flashing when the water level does not change for a period of time OR water is present but the control does not detect the water level changing.

How do I reset my Whirlpool Cabrio Top load washer?

Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.

How do I reset my Whirlpool load and go?

Method 1: Unplug it

The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.

How do you clear the error code on a Whirlpool top load washer?

System error code. Press START/PAUSE once to clear the code, then press START/PAUSE again to restart washer. If the code doesn’t clear, Contact Us or Schedule Service Online. Hot and cold inlet hoses have been installed incorrectly (reversed).

Why won’t my washer go past the wash cycle?

If your washer does not advance through the cycle or stalls at a wash or rinse fill portion, then the water inlet valve may be at fault. You should first verify that the inlet hoses do not have any kinks or restrictions and that the inlet screens are clean.

How do you know if your washing machine is clogged?

The surest and most obvious sign that your washing machine’s drain hose is clogged is if you notice that the water in your machine isn’t draining away properly. Many people first notice this after putting their laundry on the spin cycle and realizing that it’s still soaking wet at the end of the timer.

How dO I reset my washing machine?

To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.

How do you unblock a washing machine?

How to unblock Your Washing Machine (8 Easy Steps):
Turn your washing machine off at the plug. Locate the pump filter. Place a bucket, towel or even a baking tray under the pump filter. Unscrew the pump filter SLOWLY. Wait for the water to finish draining. Check to see if there is a block.

Why is my spin cycle light flashing?

Spin LED light is flashing: If an out-of-balance condition is detected by the washer, the Spin light will blink during the remaining portion of the cycle and will stay illuminated for a short time after cycle completion. In some cases, the washer may not be able to balance the load and spin up to full speed.

Why is my washer just sensing?

When Kenmore HE Washer is stuck on Sensing Cycle and not proceed to the Wash cycle, most likely one of these 3 parts malfunction: Failed Water Inlet Valve or Inlet Valve Tap is in OFF position. Shift Actuator not able to change position, before Wash cycle. Control Board malfunctioned.